Shopping basket

Sub total

£0.00

(You’ll pick your shipping method in the next step)

Proceed To Checkout

or Continue Shopping

Close Menu
Close Filters

Filters

  • Flue diameter
  • System
  • Model
  • Product type
  • Material
  • DM size
  • Pot height
  • Pot colour
  • Adapter type

Mon-Fri 9am - 4pm
[email protected]

FREE DELIVERY ON ORDERS OVER £500

PalletPallet£0.000

DM36

DM36 is the Isokern pumice chimney for a 150mm stove flue. Inner flue block and outer casing, lip-glued as you build.

22  Products


Which DM36 parts do I need?

Use it for render or for a brick stack with a corbel. Do not mix DM36 casings with DM44 or DM54. The DM calculator lists the blocks for the height.

DM36 is the Isokern Double Module system with a 150mm internal diameter inside a 360mm square, 250mm high outer casing. Schiedel lists it for smaller output inserts, stoves and solid fuel or oil cookers. Like all DM chimneys it is certified to EN 1858 (T450 N1 D 3 G(00)) and suits dry chimneys only, so not condensing, pellet or biomass appliances.

Square casing

360mm square, 250mm high.Weight: 15kg

View

Access casing

250mm high, 150mm access hole.Weight: 13kg

View

Casing and soot door

250mm high.Weight: 18kg

View

45° flue entry kit (4 parts)

500mm high.Weight: 42kg

View

Starter flue block

150mm i/d, 125mm high.Weight: 4kg

View

Flue block

150mm i/d, 255 x 255mm, 250mm high.Weight: 8kg

View

Access flue block

500mm high.Weight: 16kg

View

Offset block

86mm, 30°, 150mm high.Weight: 25kg

View

Square support block

100mm high.Weight: 15kg

View

Stainless steel adaptor

150mm i/d, 205mm o/d.

View

Corbel for brickwork

570mm square, 75mm high.Weight: 32kg

View

Capping for render

490mm square.Weight: 13kg

View

Capping for brickwork

690mm square.Weight: 31kg

View

Rain cap and top ring

Ventilated finish.

View

DM36 components

Dimensions and weights from the Schiedel Isokern brochure. Wall ties, reinforcement rods and the double soot door are shared across the DM range: stainless steel wall tie, 1m reinforcement rod and double soot door.

Connecting the appliance

  • Appliance below the chimney: the DM36 square support block sits on pre-stressed lintels or a cast-in-situ concrete slab, and a stainless steel adaptor connects the flue pipe, sealed with fibre rope. Schiedel recommends at least 600mm of flue pipe before the support block.
  • Flue pipe through the wall: use the 45° flue entry kit, with a soot door casing and access flue block below the entry. Seal the cavity with a suitable wall sleeve, and keep combustible insulation at least 1.5 times the pipe diameter from a single-wall connecting pipe.

Finishing above the roof

  • Render: render the casings above the roof with a two-part waterproof render (Schiedel recommends 1:2:5–6 cement:lime:sand undercoats and a 1:2:8–9 final coat, no coat over 15mm), then lip glue the 490mm square render capping onto the last casing and fit the ventilated rain cap and top ring.
  • Brick or stone: fit the 570mm square, 75mm high corbel just below the roof to carry the cladding, and finish with the 690mm square brickwork capping.
  • Chimney pot: set the pot at least 75mm into the capping and flaunch it 1:3; this always needs 38mm to combustibles.

Key installation points

  • Lay casings (rebate uppermost) and flue blocks (socket uppermost) together with staggered joints, starting with a starter flue block.
  • Seal every joint with lip glue: 2–3mm finished joints from 12–15mm beads, keeping the air gap clear.
  • Keep 38mm to combustibles, or zero on a straight rendered chimney with the ventilated top ring.
  • Tie external chimneys at maximum 1.5m intervals, and add reinforcement rods above 1.4m over the roof line.

For the full build sequence see the Double Module guide, and plan the blocks on the DM calculator.

DM36 parts FAQs

What does DM36 suit?

Schiedel lists DM36, with its 150mm internal diameter, for smaller output inserts, stoves and solid fuel or oil cookers.

Can I connect a stove with a 125mm outlet?

Schiedel lists a 125mm to 150mm decreaser adaptor for DM36. The pumice flue must not be smaller than the appliance spigot.

Do offset blocks change the distance to combustibles?

Yes. Schiedel requires 38mm distance to combustibles on offset chimneys.

How do I finish the top?

With the ventilated rain cap and top ring on a render capping, or a chimney pot set at least 75mm into the capping and flaunched, which needs 38mm to combustibles.

Need help choosing your DM36 parts?

Speak to our Isokern team on 0113 322 5187 or email [email protected]. We can check sizes, flue requirements and what to order.

Isokern is made by Schiedel; we are not the manufacturer.